Toxic/Combustible Dual Gas Monitor Analog Output
  • Advanced Sensing Technology:
  • Detects CO, NO2, O2, H2, H2S, CH4, C3H8
  • Wall Mount
  • Advanced electrochemical (for toxic gases)and catalytic bead (for combustible gases) sensor performance
  • Comes in standalone, standalone with remote (dual gas - mode shown here)
  • Cost Effective:
  • Saves energy through Demand Control Ventilation (DCV)
  • Remote sensor option provides dual gas monitoring (standalone version only)
  • Versatile Communications:
  • Couple with other systems via the analog output

The E3Point dual detects a wide range of toxic and combustible gases found in commercial building spaces and outdoor buildings, including CO, NO2, O2, H2, H2S, CH4 anddual gas applications C3H8. It can be used as a standalone unit with single or dual-gas detection (i.e. using a remote sensor),

E3Point can operate Demand Control Ventilation through relays, Building Automation System (BAS) or controller in order to increase energy savings, extend fan life, and align with practices of green building. In its network configuration, E3Point also optimizes HVAC, fire/smoke, surveillance, and other building systems performance.

Intelligent product design reduces the unit's cost of ownership while increasing flexibility of application. Smart sensors are pre-calibrated, auto-configured upon set-up and operate continuously on patented Reflex© technology which continuously monitors sensor cell condition and alerts user to fault status. The plug-n-play sensor cartridge, user-friendly menu and wiring options simplify installation and maintenance, and reduce the cost of gas monitoring over the life of the unit.

Portable Air Quality Monitor, CO, CO2 here 

Installation
Locating the Sensor:
Since the E3 Point units are shipped with custom network diagrams that indicate the best locations for installation, the remaining considerations are installation height and detection objectives. IF the primary application is the fastest possible leak detection, mount the sensor near the ptential leak sources. As a result, the indicated concentration may not be representative of personnel exposure, and easy access for the required calibration and maintenance can be compromised.

Air Currents:
If there are fans, wind , or other sources of air movement, gases may tend to rise or collect in certain areas of a facility. The local air currents should be assessed to aid in selecting the sensor location. Air convection can often be more important in determining gas concentration areas than factors of vapor density.

Gas Emission Sources:
As a rule, at least one sensor shouold be located in close proximity to each point where an emission is likely to occur.

Detected Gas Relative Density Installation Height
 
(air =1)
 
Carbon Monoxide
0.968
1-1.5 m (3-5 ft.) from floor
Hydrogen Sulfide
1.19
30 cm (1ft.) from floor
Nitrogen Dioxide*
1.58 (cold)
30 cm -1 m (1-3 ft.) from floor
Oxygen
1.43
1-1.5 m (3-5 ft.) from floor
COMB Most combustibles are heavier than air, with the exception of methane, hydrogen, ethylene and acetylene. Sensors for gases that are heavier than air should be installed approximately 30 cm (1ft.) from the floor. For combustibles that are lighter than air, sensors should be installed 30 cm (1ft.) from the ceiling, close to the potential leak source.
* May differ in certain applications. Hot NO2 from exhaust systems is lighter than ambient air.
General Technical Specifications
Sensor  
Input Power:


24 VAC nominal, 17-27- VA,. 50/60 Hz, 0.35 A
24 VDC nominal, 20-38 VDC

Optional main AC input power:
120 Vac nominal, +/- 10%(with on-board transformer) @ 0.35 A
Relay output: 2 DPDT relays, 5A @ 250 VAC
Communications: 4-20mA analog output
Operating Environment Commercial, indoor
Operating temperature range: H2S, N02, O2, Comb.: -40 to 50*C (-40 to 122* F)
CO: -20 to 50*C (-4* F to 122*F)
Available option CO: -40 to 50*C (-40 to 122*F)
Operating humidity range: 15 to 90% RH non-condensing
Resolution: CO= 1 ppm
O2 = 0.1% vol.
H2S= 0.1 ppm
NO2 = 0.1 ppm ,br> CH4, H2, C3H8, = 0.5% LEL
Operating Altitude: Mazimum 2000m (6562 tf)
Audible Alarm: > 85 dB at 3 m (10 ft)
Display: 8 character, 2 line LCD
Visual Indicators: Green LED: Power
Amber LED 1: Alarm/Fault
Amber LED 2: Alarm/Fault
Enclosure : Polycarbonate
Dimensions (H x W x D) 20.56 x 14.90 x 6.72 cm (8.09 x 5.87 x 2.65 in.)
Certifications CSA C22.2 No. 61010-1
UL61010
Dimensions 8.4 in.(H) x 5.3 in.(W) x 2.25 in.(D) (21.3 cm x 13.4 cm x 5.7 cm)

 

E3 Point Detection Specifications:

Sensor Type Gas Range Detection Unit Accuracy (@25*) Display Resolution
Electrochemical
CO  0/250 ppm 3% 1 ppm
Electrochemical O2 0/25 % 3% 0.1%
Electrochemical H2S 0/50 ppm 3%  0.1 ppm
Electrochemical  NO2  0/10 ppm 3% 0.1 ppm
Catalytic combustion (CH4) 0/100 (5.0% v/v) %LEL 3% 0.5%
Catalytic Combustion (H2) 0/100 (4.0% v/v) %LEL 3%  0.5%
Catalytic combustion (C3H8) 0/100 (2.1% v/v) %LEL 3% 0.5%

 

Ordering Information
  Base unit and Sensor Wall Mount
110V AC
Wall Mount
24V AC or DC
Order online
E3SASCO
E3 pt. 4-20mA 24VAC/DC CO
$535
$472 order on line
E3SASNO2
E3 pt. 4-20mA 24VAC/DC NO2
$645
$585
E3SASH2S
E3 pt. 4-20mA 24VAC/DC H2S
$645
$585
E3SASH2
E3 pt. 4-20mA 24VAC/DC H2
$645
$585
E3SASO2
E3 pt. 4-20mA 24VAC/DC O2
$645
$585
E3SASM (methane)
E3 pt. 4-20mA 24VAC/DC CH4
$645
$585
E3SASP (propane)
E3 pt. 4-20mA 24VAC/DC C3H8
$645
$585
Remote Sensors
E3SRMSCO
Carbon Monoxide Remote Sensor
$290
$290 order on line
E3SRMNO2
Nitrogen Dioxide Remote Sensor
$290
$290
E3SRMH2S
Hydrogen Sulfide Remote Sensor
$290
$290
E3SRMH2
Hydrogen Remote Sensor
$290
$290
E3SRMO2
Oxygen Remote Sensor
$290
$290
E3SRMM (methane)
Methane Remote Sensor
$290
$290
E3SRMP(propane)
Propane Remote Sensor
$290
$290

 

   Topac Inc 231 CJC Highway, Cohasset MA 02025 USA
Tel: 781 740 8778 Fax: 781 740 8779 e-mail: sales@topac.com

| Home | E-mail | Related products|

Page design and HTML Copyright ©2014 by Topac Inc. - ALL RIGHTS RESERVED